FaultCodes.org
P0028OBD-IIPowertrain & Engine ManagementTechnical Reference· Updated: Nov 22, 2026

P0028 Fault Code: Intake Valve Control Solenoid Circuit Range/Performance (Bank 2)

OBD-II P0028 (Powertrain & Engine Management): Intake Valve Control Solenoid Circuit Range/Performance (Bank 2).

Quick AnswerModerate — Plan Repair

OBD-II fault code P0028 indicates Intake Valve Control Solenoid Circuit Range/Performance (Bank 2). Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $54–$2700.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Moderate (Intermediate)
System
Powertrain & Engine Management
Professional Repair
$54 – $2,700

What This Fault Code Means

A solenoid valve routes engine oil to a valve control element on the intake side of bank 2. Depending on the manufacturer this is a valve lift changeover or a camshaft phaser. P0028 is a plausibility fault: the electrical control is in order, but the expected effect does not occur or comes too late. The control module recognises this from feedback such as an oil pressure switch or the camshaft sensor. Pure circuit faults of the same solenoid have their own codes. The engine usually remains drivable, but with less power and higher consumption. Bank 2 exists only on V and boxer engines.

Common Symptoms

  • Check engine light on
  • Loss of power, no extra pull at higher engine speed
  • Higher fuel consumption
  • Rough idle possible if a phaser is affected

Most Likely Root Causes

  • Oil level too low, wrong viscosity or sludged oil
  • Feedback oil pressure switch faulty or leaking (systems with switch)
  • Screen in front of the solenoid clogged, or solenoid sticking
  • Mechanical fault in the valve train, e.g. locking pin or phaser sticking
  • Contact resistance in wiring or connector

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0028.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Valve Control Solenoid Intake Bank2.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0028?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Valve Control Solenoid Intake Bank2.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Valve Control Solenoid Intake Bank2.
  5. 5Clear fault memory and run a verification cycle to confirm P0028 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$19 – $1,134
Professional Repair (Parts + Labor)$54 – $2,700

Frequently Asked Questions

Is it safe to keep operating with fault code P0028?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0028?

DIY replacement parts average $19–$1134, while professional service averages $54–$2700.

Will resetting P0028 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0028 fault code meaningP0028 repair costhow to fix P0028

Manufacturer & Technical Reference

OBD-II Technical Reference (Powertrain & Engine Management)

Related Fault Codes

Auto & OBD-II →
P0028 Fault Code: Intake Valve Control Solenoid… — Fixes & Cost | FaultCodes.org