FaultCodes.org
P0019OBD-IIPowertrain & Engine ManagementTechnical Reference· Updated: Nov 22, 2026

P0019 Fault Code: Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

OBD-II P0019 (Powertrain & Engine Management): Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B).

Quick AnswerModerate — Plan Repair

OBD-II fault code P0019 indicates Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B). Usually safe for short trips if no severe drivability or safety warnings are active. Typical professional repair costs $65–$4320.

Safe to Operate?
Yes (Short Term)
DIY Difficulty
Professional Recommended
System
Powertrain & Engine Management
Professional Repair
$65 – $4,320

What This Fault Code Means

The engine control module checks whether the signal of the exhaust camshaft on bank 2 (sensor B) arrives at the expected crankshaft position, usually while the camshaft phaser is in its rest position. P0019 is set when the deviation stays outside a calibrated window. The camshaft is then out of step with the crankshaft: a timing belt or chain has jumped a tooth, the chain is stretched, the phaser is stuck at an end stop, or a reluctor wheel has slipped. On engines with a single camshaft, sensor A is simply the only camshaft sensor. Bank 2 exists only on V and boxer engines.

Common Symptoms

  • Check engine light on
  • Long cranking or hard starting
  • Rough idle and loss of power
  • Chain rattle at cold start on chain-driven engines
  • Risk of valve damage on interference engines if the timing has jumped

Most Likely Root Causes

  • Timing chain stretched, or belt or chain jumped a tooth
  • Camshaft phaser stuck at an end stop, oil control valve or oil pressure faulty
  • Incorrect assembly after a belt or chain replacement
  • Camshaft or crankshaft sensor signal disturbed
  • Reluctor wheel on crankshaft or camshaft slipped

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0019.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Timing Chain.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0019?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Timing Chain.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Timing Chain.
  5. 5Clear fault memory and run a verification cycle to confirm P0019 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $1,814
Professional Repair (Parts + Labor)$65 – $4,320

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: P0019 (Powertrain & Engine Management)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $65 – $4,320

Frequently Asked Questions

Is it safe to keep operating with fault code P0019?

Usually safe for short trips if no severe drivability or safety warnings are active.

How much does it cost to repair P0019?

DIY replacement parts average $23–$1814, while professional service averages $65–$4320.

Will resetting P0019 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0019 fault code meaningP0019 repair costhow to fix P0019

Manufacturer & Technical Reference

OBD-II Technical Reference (Powertrain & Engine Management)

Related Fault Codes

Auto & OBD-II →
P0019 Fault Code: Crankshaft Position - Camshaft… — Fixes & Cost | FaultCodes.org