FaultCodes.org
P0015OBD-IIPowertrain & Engine ManagementTechnical Reference· Updated: Nov 22, 2026

P0015 Fault Code: "B" Camshaft Position - Timing Over-Retarded (Bank 1)

OBD-II P0015 (Powertrain & Engine Management): "B" Camshaft Position - Timing Over-Retarded (Bank 1).

Quick AnswerHigh — Service Soon

OBD-II fault code P0015 indicates "B" Camshaft Position - Timing Over-Retarded (Bank 1). Avoid prolonged operation until inspected to prevent secondary component damage. Typical professional repair costs $65–$2700.

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Moderate (Intermediate)
System
Powertrain & Engine Management
Professional Repair
$65 – $2,700

What This Fault Code Means

The engine control module compares the commanded position of the exhaust camshaft on bank 1 with the actual position from the camshaft and crankshaft sensors. This code is set when the camshaft stays further retarded than commanded for longer than a calibrated time. Usually the phaser does not move far enough out of its rest position, because oil pressure is too low to release the locking pin, the oil control valve does not open, or the oil screen is blocked. A stretched timing chain also shifts the camshaft towards retarded. Bank 1 is the cylinder bank that contains cylinder 1.

Common Symptoms

  • Check engine light on
  • Noticeably less torque and pulling power
  • Higher fuel consumption
  • Harder starting in some cases
  • Rattle from the timing drive if the chain is stretched

Most Likely Root Causes

  • Oil pressure or oil level too low, oil worn out
  • Oil control valve sticking closed or its screen blocked
  • Cam phaser defective or seized in its rest position
  • Timing chain stretched or jumped a tooth
  • Wear debris in the oil circuit, e.g. from a thrust bearing

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Read stored freeze-frame data and companion codes alongside P0015.
  2. 2Inspect electrical connectors, fuses, and harnesses connected to Cam Phaser Exhaust Bank1.
  3. 3Verify live sensor telemetry before ordering replacement components.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Are any companion fault codes stored alongside P0015?

Step-by-Step Troubleshooting & Fix

  1. 1Scan for companion fault codes and address upstream circuit issues first.
  2. 2Visually inspect wiring harnesses, plugs, and hoses around Cam Phaser Exhaust Bank1.
  3. 3Test component voltage, resistance, or mechanical actuation with diagnostic tools.
  4. 4Repair damaged wiring or install an OEM-grade replacement Cam Phaser Exhaust Bank1.
  5. 5Clear fault memory and run a verification cycle to confirm P0015 does not return.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$23 – $1,134
Professional Repair (Parts + Labor)$65 – $2,700

Frequently Asked Questions

Is it safe to keep operating with fault code P0015?

Avoid prolonged operation until inspected to prevent secondary component damage.

How much does it cost to repair P0015?

DIY replacement parts average $23–$1134, while professional service averages $65–$2700.

Will resetting P0015 fix the problem permanently?

No. Clearing the fault code only removes the stored alert temporarily; the code returns if the underlying fault persists.

Related Searches & Questions

P0015 fault code meaningP0015 repair costhow to fix P0015

Manufacturer & Technical Reference

OBD-II Technical Reference (Powertrain & Engine Management)

Related Fault Codes

Auto & OBD-II →
P0015 Fault Code: "B" Camshaft Position - Timing… — Fixes & Cost | FaultCodes.org