FaultCodes.org
6ABuderusFlame Detection / IgnitionVerified Guide· Updated: Nov 22, 2026

Buderus Boiler Fault 6A (227): No Flame Detected / Ionization Failure

Burner lockout paired with service code 227 after ignition attempts fail to establish stable micro-ampere (µA) ionization current—confirm external gas valves are open, press Reset once, and book a certified heating engineer.

Quick AnswerCritical — Stop Immediately

Buderus fault code 6A (paired with service code `227`) is the classic ignition and flame-detection lockout: the burner ran through its spark sequence yet the control board detected zero stable ionization current (`µA`) and shut the gas valve safely. Homeowner checks stop at confirming the main meter and under-boiler yellow gas cock are open (and checking other gas appliances/cold condensate lines), then pressing Reset once. If 6A returns, leave the combustion cover closed and call a Gas Safe / certified SHK engineer to clean or replace the ionization and ignition electrodes, measure micro-ampere (µA) flame feedback, verify gas supply inlet pressure, and inspect the gas valve/siphon ($150–$540 / €120–€450).

Safe to Operate?
No — Risk of Damage
DIY Difficulty
Professional Recommended
System
Flame Detection / Ignition
Professional Repair
$150 – $540

What This Fault Code Means

When a Buderus Logamax burner lights, a DC voltage applied to the ionization probe generates a weak flame-rectified micro-ampere (`µA`) current through ionized combustion gases to ground. If oxidization coats the ceramic/metal probe tip, spark electrodes misfire, gas pressure starves, or backed-up condensate blocks burner drainage, ionization current falls below threshold and the UBA/BC controller locks out on 6A (227).

Common Symptoms

  • Clicking ignition sparks run 3–4 times without sustaining a flame, then display latches 6A (or sub-code 227)
  • Flame lights briefly for 1–3 seconds before snapping shut because ionization feedback drops out
  • Occurs more often on the very first cold autumn/winter fire-up after months of hot-water-only idle

Most Likely Root Causes

  • Closed or partially turned gas shut-off valve / low gas inlet pressure / utility gas maintenance
  • Worn, white-crusted, or oxidized ionization sensor probe & ignition electrodes failing µA flame rectification
  • Clogged condensate siphon trap inside the boiler backing acidic water up into the combustion chamber
  • Misadjusted or failing gas combination valve, loose HT ignition lead, or faulty UBA burner PCB

Technical Thresholds & Specifications

Parameter / ConditionFactory Spec / Threshold
Buderus Code & Sub-Code Pair

No flame ionization signal detected during burner safety start time

6A / Service Code 227
Flame Detection Signal Type

Checked by service engineer in boiler diagnostics alongside combustion flue test

DC Ionization Current (µA)
Internal Combustion Safety Boundary

Homeowner checks strictly limited to external gas valve & single reset

Gas Safe / Certified SHK Engineer Only

Commonly Affected Models & Service Bulletins

  • Buderus Logamax plus GB172 / GB172i / GB192i Gas Condensing Boilers
  • Buderus Logamax plus GB112 / GB142 / GB162 Series
  • Buderus Logamax U052 / U072 & Logano Gas Heating Systems

Diagnostic Checks Before Replacing Parts

Verify the exact faulty component before ordering replacements.

  1. 1Homeowner safe check only: verify the boiler's external yellow gas valve and main gas meter valve are parallel/fully OPEN (and check whether a gas stove works or pre-pay meter ran out), plus look for frozen outdoor condensate drain pipes.
  2. 2Press Reset once on the control panel—if burner fails to hold flame cleanly after one reset, stop resetting immediately to avoid unburned gas cycling.
  3. 3Certified engineer diagnosis (never open boiler cover yourself): measure live ionization current (`µA`) via service menu/meter, measure static vs dynamic gas inlet pressure, clear internal condensate trap, and inspect electrode spark gap + earth strap.

Interactive Symptom Triage

Answer 3 quick checks to narrow down the faulty component before spending money on parts.

Check 1 of 3

Was the gas supply cock closed (or an outdoor condensate drain frozen) and did one Reset hold flame steady?

Step-by-Step Troubleshooting & Fix

Tools & Parts Reference

External gas valve & utility meter check (homeowner visual inspection only)Certified engineer: Flue gas analyzer (O2/CO/CO2) & gas inlet pressure manometerCertified engineer: OEM Buderus ignition/ionization electrode & gasket kit + µA meter
  1. 1Confirm main gas meter cock and under-boiler gas valve are fully open (and verify gas meter credit/service hasn't tripped after utility work).
  2. 2Inspect visible exterior condensate pipework in freezing weather and safely warm external ice only with warm (never boiling) water before trying one single manual Reset.
  3. 3If 6A (227) persists, leave the casing sealed and book a Gas Safe / certified SHK engineer.
  4. 4The engineer cleans/replaces the Buderus ionization & ignition electrode kit, flushes the internal condensate siphon, verifies burner combustion CO/CO2 ratios and gas valve pressure, and restores normal µA flame detection.

Estimated Repair Cost Benchmark

Typical DIY parts and certified technician labor ranges. Select a currency below.

Currency:
Repair PathUSD
DIY Parts Only$0
Professional Repair (Parts + Labor)$150 – $540

Certified Technician Service Checklist

This fault involves sealed safety, gas, or high-voltage systems. Share these details when requesting a repair quote.

  • Share exact brand & fault code: Buderus 6A (Flame Detection / Ignition)
  • Record appliance/boiler serial, model plate, or pressure reading before calling
  • Typical certified technician range: $150 – $540

Frequently Asked Questions

What does Buderus service code 227 indicate along with fault 6A?

In Buderus EMS / BC diagnostics, 6A is the lockout block display and 227 is its detailed sub-code meaning flame was not established within the safety ignition time window (missing ionization signal).

Can I sandpaper and reuse the ionization electrode myself to fix Buderus 6A?

No. Opening a Buderus combustion casing breaks critical room-sealed flue gaskets, and sanding modern coated electrodes ruins their oxide-resistant alloy layer—a certified technician must fit fresh OEM gaskets and electrodes plus verify flue combustion safety.

Related Searches & Questions

Buderus 6A 227 fault code ignitionBuderus Logamax 6A ionization electrodeBuderus boiler 6A gas reset repair costBuderus Störung 6A Flamme nicht erkannt

Verified Official & Engineering References

Plain Text / AI View

Related Fault Codes

HVAC & Boilers →
Buderus Boiler Fault 6A (227): No Flame Detected /… — Fixes & Cost | FaultCodes.org