# Buderus 6A: Buderus Boiler Fault 6A (227): No Flame Detected / Ionization Failure

> **Quick Answer:** Buderus fault code **6A** (paired with service code **`227`**) is the classic **ignition and flame-detection lockout**: the burner ran through its spark sequence yet the control board detected zero stable **ionization current (`µA`)** and shut the gas valve safely. Homeowner checks stop at confirming the main meter and under-boiler **yellow gas cock** are open (and checking other gas appliances/cold condensate lines), then pressing **Reset once**. If `6A` returns, leave the combustion cover closed and call a **Gas Safe / certified SHK engineer** to clean or replace the **ionization and ignition electrodes**, measure micro-ampere (`µA`) flame feedback, verify gas supply inlet pressure, and inspect the gas valve/siphon ($150–$540 / €120–€450).

- **URL:** https://faultcodes.org/hvac/buderus-6a
- **Category:** HVAC, Boilers & Heating
- **Brand / Standard:** Buderus
- **System Area:** Flame Detection / Ignition
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
When a Buderus Logamax burner lights, a DC voltage applied to the **ionization probe** generates a weak flame-rectified **micro-ampere (`µA`) current** through ionized combustion gases to ground. If oxidization coats the ceramic/metal probe tip, spark electrodes misfire, gas pressure starves, or backed-up condensate blocks burner drainage, ionization current falls below threshold and the UBA/BC controller locks out on `6A` (`227`).

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Buderus Code & Sub-Code Pair | 6A / Service Code 227 | No flame ionization signal detected during burner safety start time |
| Flame Detection Signal Type | DC Ionization Current (µA) | Checked by service engineer in boiler diagnostics alongside combustion flue test |
| Internal Combustion Safety Boundary | Gas Safe / Certified SHK Engineer Only | Homeowner checks strictly limited to external gas valve & single reset |

## Commonly Affected Models & Service Bulletins
- Buderus Logamax plus GB172 / GB172i / GB192i Gas Condensing Boilers
- Buderus Logamax plus GB112 / GB142 / GB162 Series
- Buderus Logamax U052 / U072 & Logano Gas Heating Systems

## Common Symptoms
- Clicking ignition sparks run 3–4 times without sustaining a flame, then display latches `6A` (or sub-code `227`)
- Flame lights briefly for 1–3 seconds before snapping shut because ionization feedback drops out
- Occurs more often on the very first cold autumn/winter fire-up after months of hot-water-only idle

## Most Likely Root Causes
- Closed or partially turned **gas shut-off valve** / low gas inlet pressure / utility gas maintenance
- Worn, white-crusted, or oxidized **ionization sensor probe & ignition electrodes** failing `µA` flame rectification
- Clogged **condensate siphon trap** inside the boiler backing acidic water up into the combustion chamber
- Misadjusted or failing **gas combination valve**, loose HT ignition lead, or faulty UBA burner PCB

## Tools & Parts Reference
- External gas valve & utility meter check (homeowner visual inspection only)
- Certified engineer: Flue gas analyzer (O2/CO/CO2) & gas inlet pressure manometer
- Certified engineer: OEM Buderus ignition/ionization electrode & gasket kit + µA meter

## Step-by-Step Troubleshooting & Fix
1. Confirm main gas meter cock and under-boiler gas valve are fully open (and verify gas meter credit/service hasn't tripped after utility work).
2. Inspect visible exterior condensate pipework in freezing weather and safely warm external ice only with warm (never boiling) water before trying **one single manual Reset**.
3. If `6A` (`227`) persists, leave the casing sealed and book a **Gas Safe / certified SHK engineer**.
4. The engineer cleans/replaces the **Buderus ionization & ignition electrode kit**, flushes the internal condensate siphon, verifies burner combustion CO/CO2 ratios and gas valve pressure, and restores normal `µA` flame detection.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$0 | $150–$540 |
| GBP | £0–£0 | £100–£390 |
| CAD | CA$0–CA$0 | CA$180–CA$650 |
| EUR | €0–€0 | €120–€450 |
| CHF | CHF 0–CHF 0 | CHF 200–CHF 690 |

## Frequently Asked Questions
### What does Buderus service code 227 indicate along with fault 6A?
In Buderus EMS / BC diagnostics, `6A` is the lockout block display and `227` is its detailed sub-code meaning flame was not established within the safety ignition time window (missing ionization signal).

### Can I sandpaper and reuse the ionization electrode myself to fix Buderus 6A?
No. Opening a Buderus combustion casing breaks critical room-sealed flue gaskets, and sanding modern coated electrodes ruins their oxide-resistant alloy layer—a certified technician must fit fresh OEM gaskets and electrodes plus verify flue combustion safety.


## Verified Official & Engineering References
- [Buderus International Support: Boiler Fault Diagnostics](https://www.buderus.com) (Official Support)
- [Buderus Deutschland Service: Störung 6A / 227](https://www.buderus.de/de/service) (Official Support)
