# Vaillant F.29: Vaillant Boiler Fault Code F.29: Flame Extinguished During Running

> **Quick Answer:** Vaillant fault code `F.29` (or `F29`) means your ecoTEC boiler **ignited cleanly at startup, then lost its flame signal while actively running**. Unlike `F.28` (zero initial ignition), `F.29` very frequently stems from a **blocked or frozen external plastic condensate pipe** backing acidic water up into the internal trap/sump until it smothers the burner flame, or from flue gas recirculation, gas pressure dips under full load, or an oxidized ionization probe. Check gas hob operation, thaw exposed exterior condensate pipes safely using **warm (never boiling) water**, and press **Reset once only**—if `F.29` returns, book a certified gas heating engineer (€0 safe checks; $140–$520 / £95–£380 professional repair).

- **URL:** https://faultcodes.org/hvac/vaillant-f29
- **Category:** HVAC, Boilers & Heating
- **Brand / Standard:** Vaillant
- **System Area:** Gas Ignition & Flame Sensing
- **Severity:** Critical — Stop Immediately
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Professional Recommended
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
While firing, the Vaillant PCB continuously reads ionization micro-amps (`µA`) across the flame probe. Because a frozen or algae-clogged outdoor condensate line forces water upward inside the boiler sump/burner tray, or a leaking inner flue pipe draws exhaust into fresh air intake, the live flame snuffs out mid-run and triggers `F.29`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Behavior vs. Vaillant F.28 | Ignites initially -> Flame lost mid-operation | Distinguishes mid-burn extinction (F.29) from start ignition failure (F.28) |
| Primary Condensate Lockout Cause | Frozen or blocked exterior condensate drain | Wastewater backs up into boiler sump/trap, smothering burner flame |
| Safe Homeowner Action Limit | Max 1 Reset after external thaw / gas check | Never boil-water plastic drains and never repeat resets without fix |
| Engineer Inspection Focus | Flue CO2 seal, load gas pressure, µA probe | Rule out flue exhaust recirculation & internal siphon clogs |

## Commonly Affected Models & Service Bulletins
- Vaillant ecoTEC plus & ecoTEC pro Gas Condensing Boilers
- Vaillant ecoTEC exclusive & ecoCOMPACT Combi/System Boilers
- Vaillant atmoTEC / turboTEC Wall-Hung Heating Units

## Common Symptoms
- Boiler lights briefly and runs for 30 seconds to several minutes before abruptly cutting out with `F.29`
- Gurgling or sloshing noise inside the boiler sump prior to flame failure (condensate backup indicator)
- Tends to lock out during freezing weather, strong winds (flue recirculation), or peak hot-water demand

## Most Likely Root Causes
- Frozen or debris/algae-clogged **external plastic condensate discharge pipe** backing water into the internal trap/sump
- Interrupted household gas flow, empty prepayment meter credit, or dynamic working gas pressure sagging under full-rate demand
- Exhaust **flue gas recirculation** (perished inner flue seal allowing CO2 exhaust into clean air intake)
- Oxidized, corroded, or carbon-fouled **ionization flame-sensing probe** or sticking gas valve coil

## Tools & Parts Reference
- Warm (non-boiling) water bottle/jug solely for frozen exterior condensate pipes
- Certified engineer flue gas analyzer (checking CO/CO2 flue recirculation)
- Certified engineer gas manometer (dynamic working pressure at full burner load)

## Step-by-Step Troubleshooting & Fix
1. Confirm steady household gas supply on kitchen gas burners (and ensure prepayment credit is positive).
2. If exterior temperatures are below freezing, gently pour **warm (never boiling)** water over exposed outdoor plastic condensate pipes—or wrap a hot towel/hot-water bottle around the frozen trap elbow—to clear trapped water.
3. Press the Vaillant **Reset** button **once** only after clearing the exterior condensate line.
4. If `F.29` returns (or sump gurgles/weather isn't freezing): call a Gas Safe / certified HVAC engineer to strip and flush the internal condensate siphon/trap, inspect coaxial flue seals for exhaust recirculation, measure dynamic working gas pressure at peak firing rate, and clean or replace the ionization probe.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$0 | $140–$520 |
| GBP | £0–£0 | £95–£380 |
| CAD | CA$0–CA$0 | CA$180–CA$620 |
| EUR | €0–€0 | €120–€430 |
| CHF | CHF 0–CHF 0 | CHF 195–CHF 660 |

## Frequently Asked Questions
### What is the exact difference between Vaillant F.28 and F.29?
**`F.28`** means zero flame established during initial ignition start-up, whereas **`F.29`** ignites cleanly at startup and then **loses the flame while actively burning**—making condensate trap backup, flue recirculation, and dropping dynamic gas pressure the classic culprits.

### How can a blocked condensate pipe smother a boiler flame and trigger F.29?
Condensing boilers drain acidic condensation water continuously while burning. When an icy or clogged outdoor pipe traps wastewater inside the sump/trap, rising water blocks exhaust flow and extinguishes the burner mid-cycle (`F.29`).


## Verified Official & Engineering References
- [Vaillant Official Fault Codes: F.29 Flame Loss Guide](https://www.vaillant.co.uk/homeowners/advice-and-knowledge/vaillant-boiler-fault-codes/) (Official Support)
- [Vaillant Homeowner Condensate & Care Advice](https://www.vaillant.co.uk/homeowners/advice-and-knowledge/) (Technical Manual)
