# Samsung 5E: Samsung Washer Error 5E / SE / 5C: Water Drain Timeout

> **Quick Answer:** Code **5E** (displayed as **SE** or **5C** on digital Samsung washers) means the machine failed to drain wash water within the control board's timeout window. Safely drain standing water using the lower-front **emergency drain tube**, unscrew and clean the **debris/pump filter**, spin the exposed pump impeller by finger to dislodge coins or hairpins, and verify the rear drain hose isn't kinked or pushed deeper than `~15 cm (6 in)` into a standpipe sitting `60–90 cm (24–35 in)` high. Cleaning a clogged trap costs $0; replacing a seized drain pump runs $25–$55 DIY ($120–$240 service).

- **URL:** https://faultcodes.org/appliances/samsung-5e
- **Category:** Home Appliances
- **Brand / Standard:** Samsung
- **System Area:** Washer Drain Circuit
- **Severity:** Moderate — Plan Repair
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Before transitioning into rinse or high-speed spin, Samsung's water level frequency sensor waits for the drain pump to evacuate the tub within roughly 3–15 minutes. If lint, socks, coins, a kinked corrugated hose, improper standpipe siphoning (`< 60 cm` or `> 90 cm` elevation), or a failed pump blocks outflow, `5E` / `SE` / `5C` halts the cycle to protect the door interlock and motor.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Equivalent Samsung Codes | 5E / SE / 5C | All denote water evacuation failure within control drain timeout |
| Official Drain Hose Elevation | 60–90 cm (24–35 in) | Standpipe or hook height above floor level per Samsung install spec |
| Max Standpipe Insertion Depth | ~15 cm (6 in) | Avoid submerging hose tip into trap water to prevent siphoning |
| Power Hard-Reset Interval | 1–2 minutes unplugged | Clears board latch after filter/impeller maintenance |

## Commonly Affected Models & Service Bulletins
- Samsung EcoBubble & AddWash Front-Load Washers (WW / WF Series)
- Samsung Bespoke AI Front-Load Washers & Washer-Dryer Combos (`5C`)
- Samsung Top-Load Washers (WA Series displaying `5E` / `SE` / `5C`)

## Common Symptoms
- Washer stops mid-cycle with standing soapy water inside the drum and `5E`, `SE`, or `5C` flashing
- Loud buzzing or grinding rattle from the lower front during drain phase with zero hose outflow
- Intermittent `5E` stops at the final spin stage even when the pump sounds clear

## Most Likely Root Causes
- Clogged lower-front **debris/coin trap filter** jammed with lint, coins, hairpins, or baby socks
- Kinked rear drain hose, blocked sink spigot, or wrong standpipe installation (outside `60–90 cm` / deeper than `15 cm`)
- Small hard object wedged behind the **drain pump impeller** blades or jammed tub-to-pump sump sock
- Burned-out drain pump motor, frozen exterior drain hose, or water-level pressure hose/sensor blockage

## Tools & Parts Reference
- Shallow pan & towels (for emergency drain tube water)
- Flashlight to inspect pump impeller blades behind filter
- Screwdriver / multimeter (only if pump replacement or coil test needed)

## Step-by-Step Troubleshooting & Fix
1. Unplug AC power, open the lower-right service flap, and drain all water via the black emergency drain tube before twisting out the **pump debris filter**.
2. Scrub lint/scale off the filter basket, reach into the pump cavity for hidden coins/buttons/hairpins so the impeller turns smoothly, and inspect the black rubber sump hose if water trickled slowly into the emergency tube.
3. Straighten any rear drain hose kinks, clean the sink trap spigot if connected under-sink, and secure the standpipe end at `60–90 cm` elevation (`~15 cm` insertion depth).
4. Reinstall the filter tightly until flush, unplug for 1–2 minutes to reset board memory, and run a Rinse+Spin test; if the pump hums loudly with clear filter/hoses or gets zero power, replace the drain pump motor (or verify pump harness continuity).

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$55 | $120–$240 |
| GBP | £0–£45 | £90–£180 |
| CAD | CA$0–CA$75 | CA$150–CA$290 |
| EUR | €0–€50 | €110–€220 |
| CHF | CHF 0–CHF 70 | CHF 160–CHF 310 |

## Frequently Asked Questions
### Why do Samsung washers display SE, 5E, or 5C for the exact same issue?
Samsung digital LED displays use the same 7-segment characters for `5` and `S` (`5E` vs `SE`) and later EcoBubble/Bespoke models standardized on `5C` (`5` = drain system check); all three represent a drain pump timeout.

### Why does pushing the drain hose too deep into a standpipe cause 5E?
Official Samsung installation specs limit standpipe insertion to ~15 cm (6 in) and outlet height to 60–90 cm (24–35 in). Pushing the hose deeper into standing drain water creates back-pressure or siphoning loops that trip the level sensor.


## Verified Official & Engineering References
- [Samsung Support US: Washing Machine Error Codes 5E / SE / 5C](https://www.samsung.com/us/support/) (Official Support)
- [Samsung Support Deutschland: Waschmaschine Fehlercode 5E / 5C](https://www.samsung.com/de/support/) (Official Support)
- [Samsung UK Home Appliances Support: Drain Filter Maintenance](https://www.samsung.com/uk/support/home-appliances/) (Official Support)
