# OBD-II P0442: Evaporative Emission (EVAP) System Small Leak Detected (0.040" / 1 mm)

> **Quick Answer:** Code P0442 indicates a small fuel-vapor leak in the EVAP system—for instance, Ford's running test detects a **0.040 in (1 mm)** orifice when pressure rises `> 2.5 inH2O` within 15 seconds after sealing (`0.020 in` sets `P0456`), whereas GM evaluates natural key-off vacuum decay (`EONV`) down to `0.020 in` across averaged cold soaks and VW/Audi compares pump current against a reference leak. Your vehicle remains completely safe to drive normally. Inspect and tighten the **fuel cap** first (wipe the filler neck clean and replace a cracked OEM cap O-ring) before smoke-testing under-hood purge/canister hoses ($0–$65 DIY cap/hoses; $140–$340 shop).

- **URL:** https://faultcodes.org/automotive/obd2-p0442
- **Category:** Automotive & OBD-II
- **Brand / Standard:** OBD-II
- **System Area:** EVAP Emissions Control
- **Severity:** Low — Minor Issue
- **Safe to Operate?:** Yes (Short Term)
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
A sealed EVAP loop prevents raw fuel hydrocarbons from venting into the atmosphere by storing fumes in a charcoal canister until drawn through the purge valve. Because tiny hairline splits shrink and expand with temperature, the ECM compares vacuum decay (`Ford` running pull-down vs. `GM` key-off `EONV` vs. `VW/Audi` leak detection pump) and triggers P0442 when pressure bleeds faster than spec.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Ford Running Small-Leak Spec | 0.040 in (1 mm) orifice (> 2.5 inH2O / 15 s) | Smaller 0.020 in orifice triggers companion code P0456 |
| GM Key-Off Natural Vacuum (EONV) | 0.020 in (0.5 mm) leak averaged over tests | Evaluates thermal pressure decay after engine shutoff |
| VW / Audi Leak Detection Method | Leak detection pump vs reference leak | Compares pressurizing pump current draw against calibrated orifice |
| Typical EVAP Monitor Window | Fuel tank ~1/4 to 3/4 full (~15–85%) | Very full or nearly empty tanks suspend self-tests |

## Commonly Affected Models & Service Bulletins
- Ford Vehicles (Motorcraft OBD Summary 0.040 in leak spec & capless Easy Fuel funnel TSbs such as SB-10065706)
- GM Cars, Trucks & SUVs (Engine-Off Natural Vacuum 0.020 in diagnostics per Mode 6 18OBDG03A)
- VW / Audi Vehicles utilizing electric EVAP leak detection pumps & reference orifices

## Common Symptoms
- Steady Check Engine Light with zero drivability, idle, or acceleration issues
- Faint gasoline odor near the rear wheel well or fuel filler door on warm afternoons
- Failed emissions inspection or companion `P0456` / `P0457` EVAP codes

## Most Likely Root Causes
- Loose, cross-threaded, or dry-rotted **fuel filler cap** rubber O-ring (or dirty capless filler funnel flap — #1 cause)
- Small split, brittle elbow, or rodent bite on engine-bay EVAP purge hoses or rear canister lines
- Slightly weeping **EVAP Canister Vent Solenoid** valve seat or cracked charcoal canister seam
- Leaking **Fuel Tank Pressure (FTP) sensor** grommet or rusted fuel-pump module lock ring atop tank

## Tools & Parts Reference
- OBD-II scanner (to verify EVAP monitor status & clear P0442)
- OEM replacement gas cap (if gasket cracked)
- Low-pressure (~1 psi) automotive EVAP smoke machine
- Fuel-vapor-rated rubber hose & pick tool (for quick-connects)

## Step-by-Step Troubleshooting & Fix
1. Tighten the gas cap past 3 crisp clicks (or wipe grime off capless filler seals cleanly); if rubber looks cracked, install a genuine **OEM replacement fuel cap** (generic locking caps frequently leak again!).
2. Clear P0442 or complete 2–4 cold-to-warm driving trips with tank level between **1/4 and 3/4 full** (the EVAP monitor pauses near empty or dead full).
3. If P0442 returns, inspect and replace split under-hood EVAP rubber hoses or a dirty/sticky purge solenoid.
4. Have a shop smoke-test the EVAP loop at low pressure (~1 psi) to pinpoint weeping rear canister vent seals, cracked fuel-filler necks, or FTP sensor grommets cleanly.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$65 | $140–$340 |
| GBP | £0–£52 | £110–£265 |
| CAD | CA$0–CA$85 | CA$185–CA$445 |
| EUR | €0–€60 | €125–€310 |
| CHF | CHF 0–CHF 75 | CHF 165–CHF 385 |

## Frequently Asked Questions
### Why does P0442 take days to turn back off after tightening a gas cap?
EVAP leak monitors only run under narrow conditions—typically fuel level between **15% and 85%**, steady cruising or engine-off cold soak (`EONV`), and mild ambient temperatures—and often require two passing tests before clearing the MIL automatically.

### Should I use an aftermarket locking gas cap for P0442?
No. Cheap universal and aftermarket locking gas caps frequently fail to seal within tight `0.020–0.040 in` OBD tolerances and end up keeping P0442 active—use an OEM factory cap.


## Verified Official & Engineering References
- [Ford Motorcraft Gasoline OBD Operations Summary](https://www.fordservicecontent.com/Ford_Content/catalog/motorcraft/OBD-Operations-Summary-Gasoline-2020-2023.pdf) (Technical Manual)
- [GM Engine OBD Diagnostics Mode 6 Reference](https://gsi.ext.gm.com/gmspo/mode6/pdf/2018/18OBDG03A%20Engine%20Diagnostics.pdf) (Technical Manual)
- [NHTSA Service Bulletin SB-10065706 (EVAP Small Leak / Seal)](https://static.nhtsa.gov/odi/tsbs/2014/SB-10065706-6903.pdf) (Service Bulletin (TSB))
