# LG LE: LG Washer Error LE: Locked Motor / Rotor Position Sensor Fault

> **Quick Answer:** Code **LE** on LG Direct Drive washing machines means the motor is locked or the **Rotor Position Sensor (Hall sensor)** did not transmit valid rotational pulses to the main control board. Start with a capacitor power reset (unplug washer, hold Power `5 s`, then Start/Pause `5 s`), check for extreme suds lock or jammed foreign objects under the drum, and then ohm-test the stator coil phases (`5–15 Ω` across U-V, V-W, W-U) and Hall sensor (`5–15 kΩ` across pins 5-1 and 5-2). Resolving a sudden overload or clearing debris costs $0, replacing a standalone Hall sensor runs ~$20–$75 DIY, and stator/PCB repairs cost $150–$320 professionally.

- **URL:** https://faultcodes.org/appliances/lg-le
- **Category:** Home Appliances
- **Brand / Standard:** LG
- **System Area:** Direct Drive Motor & Hall Sensor
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Moderate (Intermediate)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
Unlike belt-driven washers, LG Direct Drive models bolt a magnetic outer rotor shell directly around a stationary copper stator bolted to the rear outer tub (using a `17 mm` center rotor bolt). An optical/magnetic Hall Rotor Position Sensor reads magnetic pole transitions as the stator energizes three-phase windings (`U, V, W`). If spin vibration loosens the motor harness, suds drag exceeds torque limits, Hall feedback drops out, or a stator coil opens, the board cuts motor power and displays `LE`.

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Stator Winding Resistance (U-V / V-W / W-U) | 5–15 Ω | Tested unplugged across pins 1-2, 2-3, 1-3; 0 Ω or OL means bad stator |
| Hall Sensor (RPS) Resistance | 5–15 kΩ | Measured between Pin 5 & Pin 1 and Pin 5 & Pin 2 on sensor plug |
| Center Rotor Mounting Bolt | 17 mm socket | Lock drum while loosening; inspect inner rotor splines and magnets |
| Board Capacitor Reset Timing | 5 s Power + 5 s Start/Pause | Performed with mains cord unplugged before reconnecting AC power |

## Commonly Affected Models & Service Bulletins
- LG Direct Drive Front-Load Washers (WM3xxx / WM4xxx / F4V / F4WV Series)
- LG WashTower & Inverter Direct Drive Combo Washers
- LG Top-Load Direct Drive Washers (WT7xxx Series)

## Common Symptoms
- Washer fills normally, then drum shudders, hums softly, or twitches a few degrees before halting with `LE`
- Continuous `LE` lockout on empty Spin Only cycles immediately after reset
- Loud scraping or plastic burning smell when the rear magnetic rotor slips against the stator poles

## Most Likely Root Causes
- Temporary motor overload from oversized single blankets, heavy denim loads, or excessive **HE detergent suds lock**
- Faulty **Rotor Position Sensor (Hall / RPS sensor)** failing to return RPM pulses under heat or load
- Chafed, salt-corroded, or unseated 3-wire motor or 5-wire Hall sensor wiring harness (`NA1 / RD4` PCB plugs)
- Open or shorted Direct Drive stator winding coil, stripped plastic rotor splines, or burnt main PCB IPM module

## Tools & Parts Reference
- Digital multimeter (Ω / kΩ ranges for stator & Hall sensor)
- 17 mm socket + ratchet (center rotor bolt) & 10 mm socket (stator bolts)
- Phillips screwdriver for rear motor access panel
- OEM LG Rotor Position Sensor / Stator / Wiring Harness (if faulty)

## Step-by-Step Troubleshooting & Fix
1. Perform the capacitor reset (`Power` 5 s + `Start/Pause` 5 s unplugged) and run a zero-detergent hot tub clean if oversudsing caused hydraulic drag.
2. Unplug the washer, inspect rear wire harnesses from the stator/RPS up to the control board (`NA1 / RD4`), repair any chafed leads, and snap connectors firmly closed.
3. Remove the `17 mm` center rotor bolt while stabilizing the drum, inspect inner rotor splines and magnets for cracks, and replace any reading-failed **Hall RPS sensor** (`#6501KW2001A` or integrated stator depending on revision).
4. If stator phases read `0 Ω` or `OL`, swap the stator assembly; if stator, Hall sensor, and harness all test within `5–15 Ω` and `5–15 kΩ` yet `LE` persists on an empty spin, replace the main control board (PCB).

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$75 | $150–$320 |
| GBP | £0–£60 | £115–£250 |
| CAD | CA$0–CA$95 | CA$195–CA$410 |
| EUR | €0–€70 | €135–€290 |
| CHF | CHF 0–CHF 90 | CHF 190–CHF 390 |

## Frequently Asked Questions
### Can a coin or sock inside the drum trigger LG error LE?
Yes—if an item wedges between the inner stainless basket and outer plastic tub, it mechanically locks the rotor. Spin the drum manually by hand; any scraping or stiff spot points to a trapped object or seized tub bearing.

### Why can an LG Hall sensor read 10 kΩ cold yet still cause LE?
Hall-effect integrated circuits frequently pass static cold ohm checks (`5–15 kΩ`) on the bench yet drop out thermally under active motor load, so repeating the ohm test or swapping an aging standalone RPS often cures intermittent `LE` stops.


## Verified Official & Engineering References
- [LG US Help Library: Direct Drive Motor & LE Error Troubleshooting](https://www.lg.com/us/support/help-library) (Official Support)
- [LG Deutschland Support: Waschmaschine Fehlercode LE](https://www.lg.com/de/support) (Official Support)
- [LG UK Product Support: Direct Drive Motor Reset & Diagnosis](https://www.lg.com/uk/support/product-help) (Official Support)
