# Buderus H07: Buderus Boiler Fault H07 (1017): Heating System Water Pressure Too Low

> **Quick Answer:** Buderus code **H07** (paired with diagnostic code **`1017`**) indicates **low heating system water pressure**: static pressure has dropped below the safe minimum threshold (blocking below ~`0.2–0.8 bar` depending on sensor configuration), halting burner firing to protect the heat exchanger against dry-boiling. Look at the boiler's bar pressure gauge: safely open the external **filling loop / tap** slowly until cold static pressure climbs back to **`1.0–1.5 bar`**, bleed trapped radiator air (topping back to `~1.5 bar` afterward), and close the filling valve tightly. Topping up costs $0; if pressure drops back under `1.0 bar` within days or weeks, a **certified SHK / Gas Safe engineer** must inspect leaks, pressure relief drips, or a deflated **expansion vessel** ($100–$340 / €90–€310).

- **URL:** https://faultcodes.org/hvac/buderus-h07
- **Category:** HVAC, Boilers & Heating
- **Brand / Standard:** Buderus
- **System Area:** Boiler Water Pressure
- **Severity:** High — Service Soon
- **Safe to Operate?:** No — Risk of Damage
- **DIY Difficulty:** Easy (Basic Tools)
- **Updated:** 2026-11-22T00:00:00Z

## What This Fault Code Means
A sealed Buderus central heating loop relies on pressurized water (`1.0–1.5 bar` cold) so the circulation pump never cavitates or overheats the primary exchanger. As air slowly bleeds out, a radiator valve weeps, or a waterlogged expansion vessel pushes water out the safety relief valve on heating cycles, pressure falls until the electronic pressure transducer logs `H07` (`1017`).

## Technical Thresholds & Specifications
| Parameter / Condition | Factory Spec / Threshold | Note |
| --- | --- | --- |
| Buderus Status & Sub-Code Pair | H07 / Service Code 1017 | Indicates central heating loop water pressure dropped below threshold |
| Recommended Cold Operating Pressure | 1.0–1.5 bar (target ~1.5 bar) | Never exceed ~2.5–3.0 bar cold; bleed air & re-top carefully |
| Fault Trigger Range | < 0.2–0.8 bar (model-dependent) | Halts burner firing to safeguard heat exchanger against dry-heat stress |

## Commonly Affected Models & Service Bulletins
- Buderus Logamax plus GB172 / GB172i / GB192i Gas Condensing Boilers
- Buderus Logamax plus GB182i / GBH172 Hybrid Heating Systems
- Buderus Logano plus Floor-Standing Condensing Boilers

## Common Symptoms
- Display flashes `H07` (and `1017` under service history) while radiators stay cold
- Front analog or digital manometer gauge shows under `0.8 bar` (often near `0.0–0.4 bar`)
- Upper-floor radiators gurgle or stay cold at the top prior to lockout

## Most Likely Root Causes
- Normal gradual water/air loss after **bleeding radiators** without re-topping cold system pressure
- Small unseen **pipe, radiator valve, or auto-air-vent weep** slowly draining loop pressure
- Deflated air cushion or ruptured diaphragm inside the **expansion vessel (MAG)** blowing water out the PRV when hot
- Faulty or sludge-fouled **boiler water pressure transducer** reading artificially low bar

## Tools & Parts Reference
- External filling loop hose / boiler fill tap (safe pressure top-up to 1.5 bar)
- Radiator bleed key & cloth (for venting upper-floor radiators)
- Certified engineer (if recurrent): Expansion vessel pump gauge & OEM pressure sensor

## Step-by-Step Troubleshooting & Fix
1. Turn heating off or let the system cool slightly, connect the external filling hose (or turn the integral filling key/valve slowly) while watching the pressure gauge.
2. Raise cold static pressure cleanly to **`1.2–1.5 bar`** (never exceed `2.5–3.0 bar`), then shut both ends of the filling loop firmly so pressure can't creep over-spec.
3. Bleed air out of each radiator from ground floor upward until solid water appears, re-checking and re-topping the boiler back to `1.2–1.5 bar`; `H07` clears automatically or with one Reset.
4. If gauge pressure drops again below `1.0 bar`—or swings sharply `> 2.5 bar` while hot—keep the casing closed and call a **certified SHK / Gas Safe engineer** to recharge/replace the expansion vessel, PRV, or fouled pressure sensor.

## Estimated Repair Cost Benchmark
| Currency | DIY Parts Only | Professional Repair (Parts + Labor) |
| --- | --- | --- |
| USD | $0–$20 | $100–$340 |
| GBP | £0–£15 | £80–£260 |
| CAD | CA$0–CA$25 | CA$135–CA$430 |
| EUR | €0–€20 | €90–€310 |
| CHF | CHF 0–CHF 30 | CHF 140–CHF 440 |

## Frequently Asked Questions
### What pressure should a Buderus boiler read to fix H07?
Aim for **`1.0 to 1.5 bar`** (`~1.5 bar` target) when the heating system is cool. Above `2.5–3.0 bar` risks opening the safety relief valve.

### Why does Buderus show 1017 alongside H07?
`H07` is the operator status/block identifier for low water pressure, while `1017` is Buderus EMS's service sub-code indicating system pressure dropped below the minimum operating bar threshold.


## Verified Official & Engineering References
- [Buderus Official Support & Customer Care](https://www.buderus.com) (Official Support)
- [Buderus Deutschland Service: Wasserdruck & Störung H07](https://www.buderus.de/de/service) (Official Support)
